Enzotech SCW-REV.A User Manual download pdf

CAUTION!

OUTLET

INLET

1 2 3 4 5 6 7 8 9

*Please read this manual thoroughly before installation

User’s Manual

(English Version)

http:// www.enzotechusa.com http://www.enzotechnology.com

2.Specification

1.Dimension(L x W x H): 58x58x23.3mm

2.Base(L x W x H): 50x50x7mm

3.Total weight:510g

3.Components

1)Common Components

A) One (1)User’s Manuel

B) One (1)CPU Water Block

C) One (1)Mounting Bracket

D) Four(4)Innerspring Screws

E) Two (2)1/2” HI-Flow Hose Barbs

F) Two (2)Tube Clamps

H) One (1)Artic Silver

Céramique™ Thermal Grease (OEM)

2)Components for Intel (Socket 775)

J) One (1)Backplate for Socket 775

3)Components for AMD (AM2+/AM2/940)

G) Four (4)Clip Bolts

I) Four (4)Nylon Spacers

K) One (1)Type-S Retention Module (AM2+/AM2/940)

L) One (1)Backplate for AM2+/AM2/940

4.Installation

(1)Intel Pentium 4-775

1. Align back plate for”Socket 775” on the back side of the

motherboard.

2. Place CPU Water block on center of the CPU.

3. Place the mounting bracket over the water block. There are

four holes on the mounting bracket to put the metal rods

through.

4. Place innerspring screws on the four metal rods and fasten

down until all sides are level.

(2) AMD Socket AM2+/AM2/940

1. Remove the original Clip support for the AMD “socket

AM2/940” from the motherboard.

2. Align the Type-S (AM2+/AM2/940) Retention Module with the

mounting holes on the motherboard and fasten them together

using the Retention Module mounting bolts.

AM2+/AM2/940

3. Place Nylon Spacers through the 4 metal rods on the Type-S

(AM2+/AM2/940) Retention Module.

4. Place water block on center of the CPU.

5. Place the mounting bracket over the water block. There are

four holes on the mounting bracket to put the metal rods

through.

6. Place innerspring screws on the four metal rods and fasten

down until all sides are level.

5.Tubes and Fittings installations

1. Fit tubes over water block’s hose barb fittings with gaskets.

Secure tubes using the supplied hose clamps.

2. Tighten the hose clamp using a screwdriver. Make sure

clamp is tightened snuggly, do not over-tighten! Always

check for leaks before turning on power to system!

6.WARRANTY

Our products are guaranteed for 12 months from the date of

delivery to the final user against defects in materials or

workmanship. During this period, Product will be repaired or

have parts replaced, provided; (I) the products is returned

to the agent from which it was purchased: (II) the product

has not been misused, handled carelessly or other than in

accordance with any instructions provided with respect to

its use. This guarantee does not confer rights others than

those expressly set out above and does not cover any claims

for consequential loss or damage. This guarantee is offered

as an extra benefit and does not affect your statutory rights

as a consumer.

7.Important Disclosures:

Enzotech is not responsible for any damages due to external

causes,including but not limited to, improper use, problems

with electrical power, accident, neglect, alteration,repair,

improper installation, or improper testing.

1.Features:

1) Super high density, radial pattern, micro-pin design.

(0.5mm from pin to pin), provides maximum surface exposure

area for superior cooling performance.

2) Direct injection water flow design, delivers coolant straight to

CPU core. Eight return holes pulls heated water away for

extremely fast heat dissipation.

3) Metallic Mirror coating gives elegant style and superb finish.

4) Water block’s base is machined to .0003 per inch

run-out which optimizes surface contact and maximizes

thermal conductivity performance.

5) 100% leak tested and inspected direct from factory.

* Install Tubes and Fittings

Please refer to Tubes and Fittings installations on page (8)

* Install Tubes and Fittings

Please refer to Tubes and Fittings installations on page ( 8)

Precautions

-Test product for leakage away from system before installing.

All products are leak-tested prior to shipping; however,

damage can occur during shipping and subsequent handling.

Once no leakage is confirmed, proceed with the installation

and use. Always check your circuit for leaks prior to

powering-up system.

-Never use harsh chemicals to clean your water block.

Alcohol or any other harsh solvent may cause damage to

certain materials used in the manufacturing of the water

block.

-keep this product and its associated installation items away

from children.

SCW-REV.A

Total thread length greater than 6.5 mm / 0.256 inch will cause

damages to the top (cap). Enzotech will not guarantee this

type of damage due to human factor.

*Please read this manual thoroughly before installation

User’s Manual

(English Version)

http:// www.enzotechusa.com http://www.enzotechnology.com

SCW-REV.A

6.5 mm/0.256 inch

SCW-REV.A 1

Summary of Contents

Page 1 - SCW-REV.A

CAUTION!OUTLETINLET1 2 3 4 5 6 7 8 9*Please read this manual thoroughly before installationUser’s Manual(English Version)http:// www.enzotechusa.com

Comments to this Manuals

No comments

Enzotech SCW-REV.A User Manual

Browse online or download User Manual for Water equipment Enzotech SCW-REV.A. EnzoTech SCW-REV.A User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Water equipment Enzotech SCW-REV.A