Enzotech SNBW-REV.A User Manual download pdf

CAUTION!

Total thread length greater than 6.5 mm / 0.256 inch will cause

damages to the top (cap). Enzotech will not guarantee this

type of damage due to human factor.

6.5 mm/0.256 inch

1 2 3 4

7 8 9 10

http:// www.enzotechusa.com http://www.enzotechnology.com

Precautions

-Test product for leakage away from system before installing.

All products are leak-tested prior to shipping; however,

damage can occur during shipping and subsequent handling.

Once no leakage is confirmed, proceed with the installation

and use. Always check your circuit for leaks prior to

powering-up system.

-Never use harsh chemicals to clean your water block.

Alcohol or any other harsh solvent may cause damage to

certain materials used in the manufacturing of the water

block.

-keep this product and its associated installation items away

from children.

6.WARRANTY

Our products are guaranteed for 12 months from the date of

delivery to the final user against defects in materials or

workmanship. During this period, Product will be repaired or

have parts replaced, provided; (I) the products is returned

to the agent from which it was purchased: (II) the product

has not been misused, handled carelessly or other than in

accordance with any instructions provided with respect to

its use. This guarantee does not confer rights others than

those expressly set out above and does not cover any claims

for consequential loss or damage. This guarantee is offered

as an extra benefit and does not affect your statutory rights

as a consumer.

7.Important Disclosures:

Enzotech is not responsible for any damages due to external

causes,including but not limited to, improper use, problems

with electrical power, accident, neglect, alteration,repair,

improper installation, or improper testing.

1.Features

1)High density stagger fin design, provides maximum surface

exposure area for superior cooling performance.

2)Water block’s base is machined to .0003 per inch

run-out which optimizes surface contact and maximizes

thermal conductivity performance.

3)Multiple mounting systems for maximum installation versatility.

4)Compatible with most recent SLI motherboards.

5)100% leak tested and inspected direct from factory.

2.Specification

1.Dimension(L x W x H): 59.2x53.1x17.5mm

2.Base(L x W x H): 45x35x7.5mm

3.Total Weight:160g

3.Components

1.Common Components

a)One (1)User’s Manual

b)One (1)Northbridge Water Block

c)One (1)O-Ring(Pre-Assembled)

d)Two (2)1/2” HI-Flow Host Barbs

e)Two (2)Tube Clamps

f)One (1)Artic Silver Ceramique Thermal Grease (OEM)

g)One (1)Allen Wrench #2

h)One (1)Sponge (For Flip Chip Users)

I)Four (4)M3X10L Screws

One (1)Spring Mount Pack

One (1)Wire Clips Pack

One (1)Hard Mount Pack

4.Installation

(1).Spring Mount Installation

Spring Mount Pack

A) Two (2) M3x30 Screws

B) Four (4) Fiber Washers

C) Two (2) Tension Limiters

D) Two (2) Thumb Screw s

E) Two (2) Springs

F) Two (2) Nuts

1. Remove old fan/heatsink from motherboard

2. Clean the surface of the northbridge chipset and apply the

provided thermal compound evenly on the chipset surface

3. Install the two Mounting Posts/M3x30 Screw (A) as shown in the

schematic and fasten them with Nuts (F) and Washers(B)

4. Install the Sapphire Northbridge Waterblock on the northbridge

chipset. Install the Spring (E), Tension Limiters(C), and Thumb

Screw(D)

5. Gradually and alternatively fasten the Thumb Screw until the

proper tension is reached. DO NOT OVERTIGHTEN THE

THUMB SCREW

(2).Wire Clip Installation

If the mounting bracket does not interfere with the components on

the motherboard, then it is not required to remove the mounting

bracket.

If the mounting bracket does interfere with components on the

motherboard, please remove the mounting bracket, use the

spacer(B) and M3x10L Screw(C) to fasten the housing with base

plate.

Wire Clips Pack

A) Two (2) Wire Clips

B) Four (4) Spacers

C) Four (4) M3x10L Screws

1. Remove old fan/heatsink from motherboard.

2. Clean the surface of the northbridge chipset and apply the

provided thermal compound evenly on the chipset surface

3. Install the Sapphire Northbridge Waterblock on the

northbridge chipset

4. Remove the top cover and mount the bracket.Next,fasten

m3x10L screws to the base. Insert the hooks of the wire clips

underneath the loop of the MB.

(3).Hard Mount Installation

Hard Mount Pack

A) Two (2) M3x19 Screws

B) Four (4) Fiber Washers

C) Two (2) Nylon Spacers

D) Two (2) Nuts

1. Remove old fan/heatsink from motherboard

2. Clean the surface of the northbridge chipset and apply the

provided thermal compound evenly on the chipset surface

3. Insert Screws (A) thru the top of the Sapphire Northbridge

Waterblock.

4. Fasten Nylon spacers(C) and Washers(B), Place the

waterblock on the chipset and fasten it from the back of the

motherboard using the provided metal nuts (D)

Fasten the nuts alternatively and incrementally to maintain

as even pressure on the chipset as possible.

User’s Manual

(English Version)

SNBW-REV.A

http:// www.enzotechusa.com http://www.enzotechnology.com

User’s Manual

(English Version)

SNBW-REV.A

SNBW-REV.A 1

Summary of Contents

Page 1 - SNBW-REV.A

CAUTION!Total thread length greater than 6.5 mm / 0.256 inch will causedamages to the top (cap). Enzotech will not guarantee this type of damage due t

Comments to this Manuals

No comments

Enzotech SNBW-REV.A User Manual

Browse online or download User Manual for Water equipment Enzotech SNBW-REV.A. EnzoTech SNBW-REV.A User Manual

Summary of Contents

Comments to this Manuals